How to Install and Removal Governor,Rear Pump for Automatic transmission Mercedes-Benz 722

 

This instruction will show you guide on how to install and removal governor, rear pump for automatic transmission Mercedes-Benz 722

 

Preparation:

Benz DTS Monaco 8.16+Database Installation & Activation Service

How to Install Mercedes Benz DTS Monaco 8.16 Software

 

Procedures:

Screw out drain plug(4a) and drain oil

Installation note: Tighten drain plug to 14Nm. Check oil level and correct if necessary.

Remove cross member(22) together with rear engine mount.

Remove companion plate(25)

Unplug lamda sensor cable(arrow) on tunnel and disconnect mounting clips.

Completely remove exhaust support(24)

Engage parking lock

Unscrew twelve-sided collar nut(62) and pull off joint flange(64)

Installation note: Tightening torque is 12Nm, then knock the collar into the recess on the input shaft(arrow) with a suitable drift.

Benz DTS Monaco 8.16 8.08 Software Free Download

Take off disc(65)

Unscrew bolts(71), and take off rear cover(70)

Caution:

When removing the rear transmission cover, be sure that the kickdown solenoid valve is not damaged. It may be necessary to loosen the kickdown solenoid valve and turn slightly.

How to Start Perkins 1103 and 1104 Industrial Engines in Cold Weather

 

This instruction will show you guide on how to start Perkins 1103 and 1104 engines in cold weather.

Warning: Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury.

 

Preparation:

Newest Perkins EST 2020A & 2019A Full Support Free Download

Perkins SPI2 2018A Service and Parts Catalogs Download & Installation Service

 

Startability will be improved at temperatures below −18 °C (0 °F) from the use of a jacket water heater or extra battery capacity.

The following items provide a means of minimizing starting problems and fuel problems in cold weather:

engine oil pan heaters, jacket water heaters, fuel heaters and fuel line insulation.

Use the procedure that follows for cold weather starting.

Perkins EST 2021A Full Support Unexpired Installation Service

Procedures:

1. If equipped, move the throttle lever to the full throttle position before you start the engine.

2.  If equipped, turn the engine start switch to the HEAT position. Hold the engine start switch in the HEAT position for 6 seconds until the glow plug indicator light illuminates. This action will activate the glow plugs and aid in the starting of the engine.

NOTICE

Do not crank the engine for more than 30 seconds. Allow the electric starting motor to cool for two minutes before cranking the engine again.

3. While the glow plug indicator light is illuminated,turn the engine start switch to the START position and crank the engine.

Note: If the glow plug indicator light illuminates rapidly for 2 to 3 seconds, or if the glow plug indicator light fails to illuminate, a malfunction exists in the cold start system. Do not use ether or other starting fluids to start the engine.

4. When the engine starts, release the engine start switch key.

5. If the engine does not start, release the engine start switch and allow the starter motor to cool. Then, repeat steps 2 through step 4.

6. If the engine is equipped with a throttle allow the engine to idle for 3 to 5 minutes, or allow the engine to idle until the water temperature indicator begins to rise. The engine should run at low idle smoothly until speed is gradually increased to high idle. Allow the white smoke to disperse before proceeding with normal operation.

7. Operate the engine at low load until all systems reach operating temperature. Check the gauges during the warm-up period.

8. Turn the engine start switch to the OFF position in order to stop the engine.

Perkins EST 2021A Full Support Installation Service

How to Check Battery for Linde K10 K13

 

This instruction will show you guide on how to check battery for Linde K10 K13.

 

Preparation:

Linde Pathfinder Diagnostic 2019 2017 Software Free Download

Linde Pathfinder V3.6.2.11 LMH+KMS Diagnostic Software Installation Service

 

Procedures:

Electrolyte (battery acid) is toxic as well as caustic. When handling battery acid,always  adhere  to  the  prescribed  safety measures Especially  with  freshly  charged  batteries,observe explosion dangers in gasing area.

The  battery,  being  the  energy  supply,  has to be treated with care! Therefore observe:

•  Keep the battery dry and clean.

•  Charge regularly and check acid condition.

•  Check cable connections and battery plug for proper condition.

•  To protect against corrosion, apply acid free pole grease on the battery poles.

In addition, for batteries with liquid electrolyte:

•  Check the electrolyte level at regular intervals

•  Suction away spilt electrolyte using as iphon from the battery tray.

Note:

Gel batteries are subject to special charging/maintenance and treatment regulations.Always  obey the instructions issued by the relevant manufacturer.Caution Plug battery plug in or out  only when key switch is switched off. Is the battery plug pulled out when a consumer is still active, it is possible for all the contacts to burn.